E-8000 Diamond Crystal Part [B] MSDS Sheet

MATERIAL SAFETY DATA SHEET:

E-8000 Diamond Crystal [ Clear Coat] Part [ B] Curing Agent Hardener		Emergency Number Chem. Tel 1-800-255-3924

1. CHEMICAL PRODUCT IDENTIFICATION: E-8000 Diamond Crystal
Product Name: Formulation 291-22/2 Component II Product Code: E-800-B Chemical Family: Aliphatic Polyisocyanate Chemical Name: 1,6-Hexamethylene Diisocyanate Based Polyisocyanate Synonyms: Polymeric Hexamethylene Diisocyanate Formula: Not Applicable

2. COMPOSITION/INFORMATION ON INGREDIENTS:
INGREDIENT NAME /CAS NUMBER	EXPOSURE LIMITS		CONCENTRATION (%)


Homopolymer of HDI 28182-81-2
	OSHA. Not Established ACGIH: Not Established		Essentially 100%
The recommended Mobay Guideline level (MGL) for HDI based polyisocyanates is 0.5 mg/m3 (TWA -averaged over 8 hours) and 1.0 mg/m3 short term exposure (STEL - averaged over 15 minutes)

Hexamethylene Diisocyanate (HDI) 822-06-0
	OSHA: Not Established ACGIH: .005 ppm TWA		*%
Monomer content is less than 0.2 % based on resin solids at the time of manufacture Mobay also recommends a ceiling level of 0.02 ppm (Mobay Guideline Level (MGL)).

3. PHYSICAL PROPERTIES:

PHYSICAL FORM	Liquid
COLOR	Clear/Pale yellow
ODOR	Slight
MOLECULAR WEIGHT	Approximately 500 (polyisocyanates)
BOILING POINT	Approximately 446 F (230 C)
MELTING/FREEZING POINT	Not established
SOLUBILITY IN WATER	Resin is insoluble - reacts slowly with water to liberate C02 gas.
SPECIFIC GRAVITY	1.17 @ 68 F (20 C)
BULK DENSITY	9.76 lbs/gal
% VOLATILE BY WEIGHT	Negligible
VAPOR PRESSURE	Polyisocyanate: Approx. 7.5 x 10-5 mm Hg @ 20 C

4. FIRE AND EXPLOSION DATA:
FLASH POINT:		460.0 F (237.7 C) Setaflash (ASTM D-3243, D-3278, D-3828)
AUTO-IGNITION TEMPERATURE:		860 F (460 C) DIN 71794
EXTINGUISHING MEDIA:		Dry Chemical; Carbon Dioxide; Foam; Water spray for large fires.

SPECIAL FIRE FIGHTING PROCEDURES:
	Full emergency equipment with self-contained breathing apparatus and full protective clothing should be worn by firefighters. During a fire, HDI vapors and other irritating, highly toxic gases may be generated by thermal decomposition or combustion (See Section. VIII.) Closed container may explode when exposed to extreme heat or burst when contaminated with water (C02 evolved).

5. HUMAN HEALTH DATA:

ROUTE (S) OF ENTRY:
	Inhalation; Skin Contact; Skin Absorption; Eye Contact

HUMAN EFFECTS AND SYMPTOMS OF OVEREXPOSURE:
	ACUTE INHALATION
		HDI vapors or mist at concentrations above the TLV or MGL can irritate (burning sensation) the mucous membranes in the respiratory tract (nose, throat, lungs) causing runny nose, sore throat, coughing, chest discomfort, shortness of breath and reduced lung function (breathing obstruction.). Persons with a preexisting, nonspecific bronchial hyperreactivity can respond to concentrations below the TLV or MGL with similar symptoms as well as an asthma attack. Exposure well above the TLV or MGL may lead to bronchitis, bronchial spasm and pulmonary edema (fluid in lungs). These effects are usually reversible. Chemical or hypersensitive pneumonitis, with flu-like symptoms (e.g., fever, chills) has also been reported.

	CHRONIC INHALATION
		As a result of previous repeated overexposures or a single large dose, certain individuals will develop isocyanate sensitization (chemical asthma) which will cause them to react to a later exposure to isocyanate at levels well below the TLV or MGL. These symptoms, which include: chest tightness, wheezing, cough, shortness of breath or asthmatic attack, could be immediate or delayed up to several hours after exposure. Similar to many non-specific asthmatic responses, there are reports that once sensitized an individual can experience these symptoms upon exposure to dust, cold air or other irritants. This increased lung sensitivity can persist for weeks and in severe cases for several years. Chronic overexposure to isocyanates has also been reported to cause lung damage, including decrease in lung function, which may be permanent. Sensitization may be either temporary or permanent.

	ACUTE SKIN CONTACT
		Isocyanates react with skin protein and moisture and can cause irritation. Symptoms of skin irritation may be reddening, swelling, rash, scaling or blistering. Some persons may develop skin sensitization from skin contact. Cured material is difficult to remove.

	CHRONIC SKIN CONTACT
		Prolonged contact with the isocyanate can cause reddening, swelling, rash, scaling or blistering. In those who have developed a skin sensitization, these symptoms can develop as a result of contact with very small amounts of liquid material or even as a result of vapor-only exposure.

	ACUTE EYE CONTACT
		Liquid, aerosols and vapors of this product are irritating and can cause pain, tearing, reddening and swelling accompanied by a stinging sensation and/or a feeling like that of fine dust in the eyes.

	CHRONIC EYE CONTACT
		May result in corneal opacity (clouding of the eye surface).

	ACUTE INGESTION
		Can result in irritation and possible corrosive action in the mouth, stomach tissue and digestive tract.

	CHRONIC INGESTION
		None determined.

	CARCINOGENICITY
		NTP :	Not listed
		IARC :	Not listed
		OSHA :	Not regulated
		OTHER :

	MEDICAL CONDITIONS
		AGGRAVATED BY EXPOSURE : Asthma and other respiratory disorders (bronchitis, emphysema, hyperreactivity), skin allergies, eczema.

	EXPOSURE LIMITS :
		Not established for product as a whole. Refer to Section II for exposure limits of hazardous constituents. The Mobay Guideline Level of 0.5 mg/m3 - TWA and 1.0 mg/m3 - STEL for the Homopolymer of HDI and 0.02 ppm ceiling for HDI monomer are internal guides based on limited data; they are provided as guides pending the review of future data.

6. EMERGENCY AND FIRST AID PROCEDURES:
FIRST AID FOR EYES:
	Flush with clean, lukewarm water (low pressure) for at least 15 minutes while holding eyelids open. Refer individual to physician or ophthalmologist for immediate follow-up.
FIRST AID FOR SKIN:
	Remove contaminated clothing immediately. Wash affected areas thoroughly with soap and water. Wash contaminated clothing thoroughly before reuse. For severe exposures, get under safety shower after removing clothing, then get medical attention. For lesser exposures seek medical attention if irritation develops or persists.
FIRST AID FOR INHALATION:
	Move to an area free from risk of further exposure. Administer oxygen or artificial respiration as needed. Obtain medical attention. Asthmatic-type symptoms may develop and may be immediate or delayed up to several hours. Treatment is essentially symptomatic. Consult physician.
FIRST AID FOR INGESTION:
	DO NOT INDUCE VOMITING. Give a glass of milk or water to drink. DO NOT GIVE ANYTHING BY MOUTH TO AN UNCONSCIOUS PERSON. Consult a physician.
NOTE TO PHYSICIAN:
	Eyes: Stain for evidence of corneal injury. If cornea is burned, instill antibiotic/steroid preparation frequently. Workplace vapors could produce reversible corneal epithelial edema impairing vision. Skin: This product is a known skin sensitizer. Treat symptomatically as for contact dermatitis or thermal burn. Ingestion: Treat symptomatically. There is no specific antidote. Inducing vomiting is contraindicated because of the irritating nature of the product. Inhalation: This product is a known pulmonary sensitizer. Treatment is essentially symptomatic. An individual having a dermal or pulmonary sensitization reaction to this material must be removed from any further exposure to any isocyanate.

7. EMPLOYEE PROTECTION RECOMMENDATIONS:
REQUIRED WORK/HYGIENE PROCEDURES:
	Precautions must be taken so that persons handling this product do not breathe the vapors or have it contact the eve or skin. In spray operations, protection must be afforded against exposure to both vapor and spray mist.
EYE PROTECTION REQUIREMENTS:
	Liquid chemical goggles or full-face shield. Contact lenses should not be worn.
SKIN PROTECTION REQUIREMENTS:
	Permeation resistant gloves (butyl rubber, nitrile rubber). Cover as much of the exposed skin area as possible with appropriate clothing. If skin creams are used, keep the area protected only by the cream to a minimum.
RESPIRATORY/VENTILATION REQUIREMENT:
	A respirator that is recommended or approved for use in isocyanate containing environments (air purifying or fresh air supplied) may be necessary. Consider type of application and environmental concentrations. Observe OSHA regulations for respirator use (29 CFR 1910.134) Exhaust ventilation sufficient to keep the airborne concentrations of HDI and polyisocyanate below their respective TLV and MGL must be utilized. Exhaust air may need to be cleaned by scrubbers or filters to reduce environmental contamination
NOTE ON ODOR WARNING PROPERTIES:
	Pure isocyanate materials have odor thresholds that are higher than the TLV, PEL or MGL. Thus, if a vapor/particulate air-purifying respirator has exceeded its service life, breakthrough of the filter can result in exposure over the allowable limit without the wearer being able to smell the isocyanate. However, when a polyurethane coating system contains organic solvents, the wearer of a vapor particulate respirator will be warned of filter breakthrough by the odor of solvents before being exposed to isocyanates because: 1) organic solvents have low odor thresholds, and 2) testing has demonstrated that solvents break through filters before isocyanates do. SPRAY APPLICATION: A. Good industrial hygiene practice dictates that when isocyanate based coatings are spray applied, some form of respiratory protection should be worn. During the spray application of organic solvent containing coatings systems, the use of a positive pressure supplied air respirator is mandatory when: - the airborne isocyanate concentrations are not known, or - the airborne HDI monomer concentrations exceed 0.05 ppm (10 times the TLV) or the polyisocyanate (polymeric, oligomeric) concentrations exceed 5 mg/m3 averaged over 8 hours or 10 mg/m3 averaged over 15 minutes (10 times the MGL) or - spraying is performed in a confined space or in an area with limited ventilation. A properly fitted air-purifying (combination organic vapor and particulate) respirator, proven by test to be effective in isocyanate-containing spray paint environments, will provide adequate protection when: - the airborne HDI monomer concentrations are known to be below 0.05 ppm (10 times the TLV), and - the polyisocyanate (polymeric, oligomeric) concentrations are known to be below 5 mg/m3 averaged over 8 hours or 10 mg/m3 averaged over 15 minutes (10 times the MGL). B. During the spray application of a coatings system NOT containing organic solvents a positive pressure supplied air respirator is mandatory when: - the airborne isocyanate concentrations are unknown, or - the airborne isocyanate monomer concentration exceeds the TLV of 0.005 PPM, or -the polyisocyanate (polymeric, oligomeric) concentration exceeds the MGL of 0.5 mg/m3 averaged over 8 hours, or - operations are performed in a confined space or in an area with limited ventilation. Under any other circumstances, during spray application of a coatings system NOT containing organic solvents, good industrial hygiene practice dictates that when isocyanate based coatings are spray applied some form of respiratory protection should be worn. NON-SPRAY OPERATIONS: A. Even during non-spray operations such as mixing, batch making, brush or roller application, etc., depending on the conditions (for example, heating of material or application to a hot substrate), it is possible to be exposed to airborne isocyanate vapors. Therefore, when the coatings system contains solvents and will be applied in a non- spray manner, a positive pressure supplied air respirator must be worn when: - the airborne concentrations are unknown; or - the airborne HDI monomer concentrations exceed 0.05 ppm (10 times the TLV), or - the airborne concentrations of the polyisocyanate (polymeric, oligomeric) exceed 5 mg/m3 averaged over 8 hours or 10 mg/m3 averaged over 15 minutes (10 times the MGL), or - operations are performed in a confined space or in an area with limited ventilation. At least an air purifying (organic vapor) respirator is required when: - the airborne concentrations of the HDI monomer exceed the TLV of 0.005 ppm but are below 0.05 ppm (10 times the TLV), or - the airborne concentrations of the polyisocyanate (polymeric, oligomeric exceed the MGL of 0.5 mg/m3 averaged over 8 hours, or 1.0 mg/m3 averaged over 15 minutes but are below 10 mg/m3 (10 times the MGL). B. During non-spray operations using a solvent-free coatings system, a positive pressure supplied air respirator is mandatory when: - the airborne isocyanate concentrations are unknown, or - the airborne isocyanate monomer concentrations exceed the TLV of 0.005 ppm, or - the polyisocyanate (polymeric, oligomeric) concentrations exceed the MGL of 0.5 mg/m3 averaged over 8 hours, or 1.0 mg/m3 averaged over 15 minutes, or - operations are performed in a confined space or in an area with limited ventilation.
MONITORING:
	Refer to Patty's Industrial Hygiene and Toxicology-Volume 1 (3rd edition) Chapter 17 and volume III (1st edition) Chapter 3-for guidance concerning appropriate air sampling strategy to determine airborne concentrations.
MEDICAL SURVEILLANCE:
	Medical supervision of all employees who handle or come in contact with this product is recommended. This should include preemployment and periodic medical examinations with respiratory function tests (FEV, FVC as a minimum). Persons with asthma-type conditions, chronic bronchitis, other chronic respiratory diseases or recurrent skin eczema or sensitization should be excluded from working wit isocyanates. Once a person is diagnosed as sensitized to an isocyanate, no further exposure can be permitted.
ADDITIONAL PROTECTIVE MEASURES:
	Safety showers and eyewash stations should be available. Educate and train employees in safe use of product. Follow all label instructions. For additional information, see Mobay's "Health and Safety Information for Hexamethylene Diisocyanate Based Polyisocyanates"..

8. REACTIVITY DATA:
STABILITY:
		This is a stable material.
HAZARDOUS POLYMERIZATION:
	May occur; Contact with moisture or other materials which react with isocyanates or temperatures over 400 F (204 C) may cause polymerization.
INCOMPATIBILITIES:
		Water, amines, strong bases, alcohols, metal compounds and surface active materials.
INSTABILITY CONDITIONS:
		None determined
DECOMPOSITION PRODUCTS:
		By high heat and fire: carbon dioxide, carbon monoxide, oxides of nitrogen, HCN, HDI.
9. SPILL AND LEAK PROCEDURES:

SPILL OR LEAK PROCEDURES:
		Evacuate nonessential personnel. Remove all sources of ignition and ventilate the area. Notify appropriate authorities if necessary. Put on personal protective equipment (see Section VII). Dike or impound spilled material and control further spillage if feasible. Cover the spill with sawdust, vermiculite, Fuller's earth or other absorbent material. Pour decontamination solution over spill area and allow to react for at least 10 minutes. Collect material in open containers and add further amounts of decontamination solution. Remove containers to a safe place, cover loosely, and allow to stand for 24 to 48 hours. Wash down spill area with decontamination solutions. Decontamination solutions: nonionic surfactant Union Carbide's Tergitol TMN-10 (20%) and water (80%); concentrated ammonia (3-8%), detergent (2%) and water (90-95%).
NEUTRALIZATION CHEMICALS
		N/A
WASTE DISPOSAL METHOD:
		Waste must be disposed of in accordance with federal, state and local environmental control regulations. Incineration is the preferred method. Empty containers must be handled with care due to product residue. Decontaminate containers prior to disposal. DO NOT HEAT OR CUT EMPTY CONTAINER WITH ELECTRIC OR GAS TORCH. (See Section IV and VIII).
10. SPECIAL PRECAUTIONS & STORAGE DATA:
STORAGE TEMPERATURE (MIN/MAX):
		-30 F (-34 C)/122 F (50 C)
SHELF LIFE:
		6 months @ 77 F (25 C) after receipt of material by customer.
SPECIAL SENSITIVITY:
		If container is exposed to high heat, it can be pressurized and possibly rupture explosively. HDI reacts slowly with water to form C02 gas. This gas can cause sealed containers to expand and possibly rupture explosively.
HANDLING/STORAGE PRECAUTIONS:
		Store in tightly closed containers to prevent moisture contamination. Do not reseal if contamination is suspected. At maximum storage temperatures noted, material may slowly polymerize without hazard. Ideal storage temperature range for ease of handling is 50-81 F (10-27 C). Avoid contact with skin and eyes. Employee education and training in the safe use and handling of this product are required under the OSHA Hazard Communication Standard.

11. SHIPPING INFORMATION:
TECHNICAL SHIPPING NAME:	Polyisocyanate
FREIGHT CLASS BULK	Isocyanate
FREIGHT CLASS PACKAGE	Chemicals, NOI (Isocyanate), NMFC 60000
PRODUCT LABEL	G.P.# 33
DOT (HM-181) (DOMESTIC SURFACE)
PROPER SHIPPING NAME	None
HAZARD CLASS OR DIVISION	Non-Regulated
UN/NA NUMBER	None
PACKAGING GROUP
DOT PRODUCT RQ lbs (kgs)
HAZARD LABEL (s)
HAZARD PLACARD (s)
IMO/ IMDG CODE (OCEAN)
PROPER SHIPPING NAME
HAZARD CLASS DIVISION NUMBER
UN NUMBER
PACKAGING GROUP
HAZARD LABEL (s)
HAZARD PLACARD (s)
ICAO / IATA (AIR)
PROPER SHIPPING NAME
HAZARD CLASS DIVISION NUMBER
UN NUMBER
SUBSIDIARY RISK
PACKING GROUP
HAZARD LABEL (s)
RADIOACTIVE?
PASSENGER AIR - MAX. QTY
PASSENGER INSTRUCTION NUMBER
CARGO AIR -MAX. QTY
CARGO AIR INSTRUCTION NUMBER

12. ANIMAL TOXICITY DATA:
TOXICITY DATA FOR: HDI homopolymer materials except where indicated

ACUTE TOXICITY
ORAL LD50:
	Estimated to be greater than 10000 mg/kg (rats). (Based on the results of actual tests conducted using specific HDI-homopolymer products.)
DERMAL LD50:
	Estimated to be greater than 5000 mg/kg (rabbits). (Based on the results of actual tests conducted using specific HDI-homopolymer products.)
INHALATION LC50:
	Lower respiratory (pulmonary) irritant. LC50 values range from 137-1150 mg/m3 were obtained in rats exposed to aerosols. (4H exp.)
EYE EFFECTS:
	Severe irritant capable of inducing corneal injury (Rabbit); maximum primary eve irritation score: 54.G/110 for a 24 hr. exposure.
SKIN EFFECTS:
	Moderate irritant; primary dermal irritation score:3.4/8.0 (rabbit)
SENSITIZATION :
	Pulmonary and dermal sensitizer in humans. Delayed dermal sensitization. was observed in guinea pigs. However, the respiratory sensitization potential of Desmodur N-3300 assessed in guinea pigs was negative. Evidence exists that cross-sensitization between HDI and other isocyanates, particularly hydrogenated MDI and TDI, can occur.
OTHER ACUTE EFFECTS:
	AMES TEST: Negative for Desmodur TI-100 (100 solids material).
SUBCHRONIC TOXICITY:
	Rats exposed to a HDI homopolymer (isocyanurate type, specifically, the solvent-free Desmodur N-3300), at 4.3, 14.7 and 89.8 mg/m3 for three weeks (6 hrs/day, S days/wk) exhibited respiratory distress and inflammation of the nasal passages at 14.7 mg/m3 and above. At the 89.8 mg/m3 inflammatory lesions at many sites of the lungs were also observed. The No Observable Effect Level (NOEL) was 4.3 mg/m3. Rats were also exposed t an HDI homopolymer (isocyanurate type, specifically, the solvent-free product Desmodur N-3300), for 13 weeks (6 hrs/day, 5 days/wk) at aerosol concentrations of 0.5, 3.3 and 26.4 mg/m3. Body weight gain of male rats of the 26.4 mg/m3 group were slightly reduced toward the end of the study. The lung weight to body weight ratio was significantly increased in the male and female rats of the 26.4 mg/m3 group. Histopathoiogic diagnosis of these animals revealed inflammatory changes and formation of fibrous tissue at the point of injury in the respiratory tract. In addition, the lung function tests at the end of the, study provided evidence of a chronic obstructive lung disorder in rats of the 26.4 mg/m3 group. The No Observable Effect Level (NOEL) in this study is considered to be 3.3 mg/m3.

OTHER TOXICITY DATA:
	Mice were exposed to a liquid aerosol of an HDI homopolymer (isocyanurate type, specifically, the solvent-free product Desmodur N-3300), mixed with acetone for three hours. The Irritation potential expressed as the RD50 (the concentration which is predicted to reduce the respiratory rate 50%) was 20.8 mg/m3 (95% confidence interval = '_8.3 to 23.9 mg/m3). Pulmonary (lung) irritation was observed first, followed by sensory (eve, nose, and throat) irritation.

13. FEDERAL REGULATORY INFORMATION:
OSHA STATUS :
	This product is hazardous under the criteria of the Federal OSHA Hazard Communication Standard 29 CFR 1910.1200.
TSCA STATUS :
	On TSCA Inventory
CERCLA REPORTABLE QUANTITY:
	None
SARA TITLE III:
	SECTION 302 EXTREMELY HAZARDOUS SUBSTANCES
		None
	SECTION 311/312 HAZARD CATEGORIES
		Immediate Health Hazard; Delayed Health Hazard
	SECTION 313 TOXIC CHEMICALS
		None
	RCRA STATUS
		When discarded in its purchased form, this product meets the criteria of ignitability, and should be managed as a hazardous waste (EPA Hazardous Waste Number D001).(40 CFR 261.20-24)

14. OTHER REGULATORY INFORMATION:

The following chemicals are specifically listed by individual states; other product specific health and safety data in other sections of the MSDS may also be applicable for state requirements. For details on your regulatory requirements you should contact the appropriate agency in your state.

MATERIAL SAFETY DATA SHEET:

E-8000 Diamond Crystal [ Clear Coat] Part [ B] Curing Agent Hardener

1. CHEMICAL PRODUCT IDENTIFICATION: E-8000 Diamond Crystal

2. COMPOSITION/INFORMATION ON INGREDIENTS:

INGREDIENT NAME /CAS NUMBER

EXPOSURE LIMITS

CONCENTRATION (%)

3. PHYSICAL PROPERTIES:

PHYSICAL FORM

COLOR

ODOR

MOLECULAR WEIGHT

BOILING POINT

MELTING/FREEZING POINT

SOLUBILITY IN WATER

SPECIFIC GRAVITY

BULK DENSITY

% VOLATILE BY WEIGHT

VAPOR PRESSURE

4. FIRE AND EXPLOSION DATA:

FLASH POINT:

AUTO-IGNITION TEMPERATURE:

EXTINGUISHING MEDIA:

SPECIAL FIRE FIGHTING PROCEDURES:

5. HUMAN HEALTH DATA:

ROUTE (S) OF ENTRY:

HUMAN EFFECTS AND SYMPTOMS OF OVEREXPOSURE:

ACUTE INHALATION

CHRONIC INHALATION

ACUTE SKIN CONTACT

CHRONIC SKIN CONTACT

ACUTE EYE CONTACT

CHRONIC EYE CONTACT

ACUTE INGESTION

CHRONIC INGESTION

CARCINOGENICITY

MEDICAL CONDITIONS

EXPOSURE LIMITS :

6. EMERGENCY AND FIRST AID PROCEDURES:

FIRST AID FOR EYES:

FIRST AID FOR SKIN:

FIRST AID FOR INHALATION:

FIRST AID FOR INGESTION:

NOTE TO PHYSICIAN:

7. EMPLOYEE PROTECTION RECOMMENDATIONS:

REQUIRED WORK/HYGIENE PROCEDURES:

EYE PROTECTION REQUIREMENTS:

SKIN PROTECTION REQUIREMENTS:

RESPIRATORY/VENTILATION REQUIREMENT:

NOTE ON ODOR WARNING PROPERTIES:

MONITORING:

MEDICAL SURVEILLANCE:

ADDITIONAL PROTECTIVE MEASURES:

8. REACTIVITY DATA:

STABILITY:

HAZARDOUS POLYMERIZATION:

INCOMPATIBILITIES:

INSTABILITY CONDITIONS:

DECOMPOSITION PRODUCTS:

9. SPILL AND LEAK PROCEDURES:

SPILL OR LEAK PROCEDURES:

NEUTRALIZATION CHEMICALS

WASTE DISPOSAL METHOD:

10. SPECIAL PRECAUTIONS & STORAGE DATA:

STORAGE TEMPERATURE (MIN/MAX):

SHELF LIFE:

SPECIAL SENSITIVITY:

HANDLING/STORAGE PRECAUTIONS:

11. SHIPPING INFORMATION:

TECHNICAL SHIPPING NAME:

FREIGHT CLASS BULK

FREIGHT CLASS PACKAGE

PRODUCT LABEL

DOT (HM-181) (DOMESTIC SURFACE)

PROPER SHIPPING NAME

HAZARD CLASS OR DIVISION

UN/NA NUMBER

PACKAGING GROUP

DOT PRODUCT RQ lbs (kgs)

HAZARD LABEL (s)

E-8000 Diamond Crystal
[ Clear Coat] Part [ B]
Curing Agent Hardener

INGREDIENT NAME
/CAS NUMBER

INGREDIENT NAME
/CAS NUMBER