Product Information:
E-8000 DIAMOND CRYSTAL
AN ACRYLIC POLYURETHANE ULTRA HARD CLEAR COAT TWO COMPONENT
USES:
ENVIROSHIELD 8000 Clearcoat IS A HIGH SOLIDS TWO COMPONENT CLEAR POLYURETHANE
FLOOR AND ANTI-GRAFFITI WALL COVERING.
THIS TECHNOLOGY IS SUITABLE FOR USE
AS A HIGH SOLIDS (3.2OVOC) Architectural AND MAINTENANCE CLEAR COATING. IT CAN
BE USED ON SURFACES WHICH REQUIRE RESISTANCE TO GRAFFITI-Removing COMPOUNDS,
AS A FLOOR COATING OR ON ANY SURFACE WHERE A CLEAR COAT IS DESIRED.
E-8000 In the News
FLOOR SYSTEMS:
ENVIROSHIELD 8000 AS EXPERIENCED BY USERS, IS ONE PART OF A
THREE PART SYSTEM FOR CONCRETE AND STEEL SUBSTRATES, WHEREBY ENVIROSHIELD 2000
IS
USED AS A PRIMER-SEALER, ENVIROSHIELD 600 IS USED AS A DURABLE COLOR
MID- COAT,
AND ENVIROSHIELD 8000 IS USED AS A HARD SURFACE COATING TO WITHSTAND HARSH
TREATMENT AND ENVIRONMENTS.
TECHNICAL DATA:
WEIGHT SOLIDS: % 63.43
WEIGHT PER GAL: 8.76 LBS.
VOLUME
SOLIDS: % 58.63
VOC LBS. PER GAL.: 3.20
GRAMS PERIL: 384
VOLUMETRIC MIX: 2.36 PART A BASE TO 1.0
PART 13 CONVERTER
FILM PROPERTIES:
TABER ABRASION ASTM D-4060-84 = 34.2 MG. LOSS
(CS-17 WHEEL,
1000GM. LOAD, 1000 CYCLES)
IMPACT, ASTM D-2194-84 DIRECT 160 IN. LBS. REVERSE
160 IN. LBS.
VISCOSITY COMPONENT ONE AND TWO 310 CPS
PENDULUM HARDNESS ASTM
D-4366-87A
MEK RESISTANCE - NO EFFECT AFTER 100 DOUBLE RUBS
RECOMMENDED D.F.T. @ 1 MIL
COATING CAN BUBBLE IF RECOMMENDED D.F.T. IS
EXCEEDED
CURING TIME TO TOUCH: 3 HRS.
TO HANDLE: 4 HRS.
TO RECOAT @ 25 DEGREES
C. @ 50% HUMIDITY: 7 HRS.
TO HARD DRY: 14 HRS.
TO HARD DRY MAR-FREE: 25 HRS.
CHEMICAL AND SOLVENT RESISTANCE:
(FOUR HOUR SPOT TEST, COVERED)
SKYROL B-4 =
NO EFFECT
HYDRAULIC FLUID #83282 = NO EFFECT
25% NITRIC ACID = BLISTERED
37% HYDROCHLORIC ACID =NO EFFECT
50% SULFURIC ACID = NO EFFECT
50% SODIUM HYDROXIDE =
NO EFFECT
10% ACETIC ACID =NO EFFECT
30% NII3OH = NO EFFECT
MEK = SLIGHT SWELLING
XYLENE = NO EFFECT
NOTES:
APPLICATION TO ABSORBENT SUBSTRATES SUCH AS CONCRETE AND ASBESTOS
REQUIRES A PRIMER TO PREVENT SAGGING OF THE BINDER. ENVIROSHIELD 200 IS
RECOMMENDED FOR PRIMER BEFORE APPLYING ENVIROSHIELD 8000 ENVIROSHIELD
600 MAY
BE TOP COATED WITH ENVIROSHIELD 8000 IF COLOR IS DESIRED, ESPECIALLY FOR STEEL
STRUCTURES AND CONCRETE FLOORS.
POT LIFE:
1/2 HOUR @ 100 DEGREES F. AND 90% R. HUMIDITY, USABLE.
1 HOUR @ 78
DEGREES F. AND 50% R. HUMIDITY, USABLE.
COVERAGE RATES: [THEORETICAL ]
1.0 MIL D.F.T. = 930 SQ. FT. PER GAL.
2.0 MIL D.F.T. = 465 SQ. FT. PER GAL.
SURFACE PREPARATION:
SURFACE MUST BE FREE OF ALL MOISTURE, DIRT, OIL, GREASE
AND OTHER CONTAMINANTS.
SAG RESISTANCE:
0.5 TO 1.0 WET MILS = NO SAG
1.5 WET MILS =5% SAG
2.5. WET
MILS =10% SAG
APPLICATION:
STIR THOROUGHLY, MAKING SURE PRODUCT IS ONE CONSISTENCY, KEEP
CONTAINER CLOSED WHEN NOT IN USE, AS PRODUCT REACTS WITH ATMOSPHERIC MOISTURE.
EQUIPMENT:
APPLY WITH ROLLER, SPRAY OR BRUSH.
SPRAY TIP SIZE: 0.009 to 0.0 13
HOSE SIZE: 1/4 TO 3/8 INCH.
CAUTION:
SURFACE TEMPERATURE MUST BE [5] DEGREES ABOVE THE DEWPOINT BEFORE
APPLYING. SURFACE TEMPERATURE SHOULD BE AT LEAST 40 DEGREES F. AND NOT EXCEED
125 DEGREES F. BEFORE APPLICATION
CLEANUP: USE XYLENE TO FLUSH AND CLEAN EQUIPMENT
IMMEDIATELY AFTER USE.
MSDS Sheet :(click here) Part 1, Part 2
| 
