PRODUCT INFORMATION:
E-401 PRIME CURE [RED] STEEL OVERCOAT SYSTEMS TM
A MOISTURE
CURE POLYURETHANE NON-LEAFING ALUMINUM PRIMER
STEEL OVERCOAT SYSTEMS E-401 IS AN ECONOMICAL, ONE
COMPONENT, MOISTURE CURE, HIGH CONTENT NON-LEAFING ALUMINUM,
HIGH SOLIDS, AND ENVIRONMENT FRIENDLY PRIMER.
COLOR: SILVER FINISH: FLAT
CHEMICAL FAMILY: POLY ISOCYANATE - PREPOLYMER
USES:
STEEL OVERCOAT SYSTEMS E-401 IS EXCELLENT FOR OVERCOATING
STRUCTURAL STEEL AND OTHER METAL SURFACES WHEN LITTLE PREPARATION
IS DESIRED. TO ACCOMMODATE FIRST STAGE ENCAPSULATION OF RUST,
CORROSION AND OLD LEAD PAINT. STEEL OVERCOAT SYSTEMS E-401
ELIMINATES THE NEED FOR SAND BLASTING WHEN 4000+ PSI WATER
DURING AND A REASONABLE AMOUNT OF POWER. AND HAND TOOL CLEANING IS
DONE. STEEL OVERCOAT SYSTEMS E-401 ABILITY TO ENCAPSULATE
OLD PAINT AND RUST IS ENHANCED WHEN A SECOND COAT 'IS USED BEFORE TOP
COATING. STEEL OVERCOAT SYSTEMS E-401 MUST BE TOP COATED
IN EVERY INSTANCE, DUE TO PRIMERS LACK OF LIGHT STABILIZERS. STEEL
OVERCOAT SYSTEMS E-401 AFFORDS HIGH RESISTANCE TO CORROSION,
MOISTURE, CHEMICALS, ABRASION AND UNDERCUTTING.
SURFACE PREPARATION:
SURFACES MUST BE FREE FROM ALL MOISTURE, DIRT, OIL, GREASE AND OTHER
CONTAMINANTS. FOR BEST RESULTS, POWER WASH AND TOOL CLEAN, THEN
BRUSH FIRST COAT OVER SUBSTRATE BEFORE APPLYING SECOND COAT WITH
BRUSH, ROLLER OR SPRAY.
PRODUCT TECHNICAL DATA:
WEIGHT SOLIDS: 69.0 +. 2.0 %.
WEIGHT PER GAL: 9.6 LBS. PER GAL.+-O.2 LBS.
PER GAL.
VOLUME SOLIDS: 59.19 % I- 1.5 %
VOC LBS. PER GAL: 2.71 LBS. GRAMS PERIL
322.1
RECOMMENDED D.F.T.: 2 - 3 MILS DRY.
| CURING TIME: |
|
TO TOUCH 3 HRS. TO HANDLE 3-4 HRS. |
|
41 TO RECOAT 4 HRS. @ 77 F. @ 50% R. HUMIDITY. |
|
TO RECOAT IN BELOW NORMAL TEMP- 24 HRS. |
STORAGE LIFE: ONE YEAR @ 77 F. (25 C)
APPLICATION PROCEDURES:
PREPARE PRODUCT BY THOROUGHLY STIRRING, MAKING SURE NO
PIGMENTS STAY ON BOTTOM. KEEP PRODUCT CONTAINER CLOSED WHEN
NOT USING, SINCE PRODUCT REACTS TO MOISTURE. DO NOT THIN, SINCE
VISCOSITY WILL REMAIN CONSTANT WHEN CONTAINER STAYS CLOSED.
APPLY WITH BRUSH, SPRAY OR ROLLER
AIRLESS SPRAY:
USE TIP SIZE 0.017 OR 0.013. HOSE SIZE: 114 TO 318
INCH. FILTER: USE 60 MESH.
RECOAT TIME:
FOR COLD WEATHER APPLICATION, A LONGER DRYING TIME IS
RECOMMENDED, A MINIMUM OF NO LESS THAN 24 HRS. WARM
TO HOT WEATHER RECOAT TIME MAY BE SHORTENED TO AS
LITTLE AS 4 HRS. *MUST BE RECOATED WITHIN 5 DAYS*.
SURFACE TEMPERATURE MUST BE AT LEAST FIVE (5 )
DEGREES ABOVE DEW POINT BEFORE APPLICATION.
FOR ADDITIONAL INFORMATION, CONTACT MANUFACTURER.
COVERAGE RATES:
5.5 MILS WET FILM THICKNESS = 175 SQ. FT. PER GAL.
5.0 MILS WET FILM THICKNESS = 195 SQ. FT. PER GAL.
4.5 MILS WET FILM THICKNESS = 210 SQ. FT. PER GAL.
4.0 MILS WET FILM THICKNESS = 235 SQ. FT. PER GAL.
3.5 MILS WET FILM THICKNESS = 275 SQ. FT. PER GAL.
3.0 MILS WET FILM THICKNESS = 315 SQ. FT. PER GAL.
2.5 MILS WET FILM THICKNESS = 375 SQ. FT. PER GAL.
2.0 MILS WET FILM THICKNESS = 475 SQ. FT. PER GAL.
1.0 MILS WET FILM THICKNESS = 946 SQ. FT. PER GAL.
SAG RESISTANCE:
NO SAG ON LENATA DRAWDOWN SCALE THROUGH 6 WET MILS.
1/32" DRAG @ 8 MILS WET.
CLEANUP:
CLEANUP: USE (XYOL) XYLENE TO FLUSH AND CLEAN IMMEDIATELY
AFTER EQUIPMENT USE. DO NOT ALLOW MOISTURE OR ALCOHOL NEAR
PRODUCT OR EQUIPMENT.
SAFETY PROCEDURES: SEE
MSDS Sheet :(click here)
| 
